Kingston's new products in the portable flash-based external storage space have met with good market reception over the last year or so. Two products in particular - the Kingston XS2000 and the DataTraveler Max - continue to remain unique in the market with no other comparable products being widely available.

The XS2000 remains the only portable SSD with a USB 3.2 Gen 2x2 (20Gbps) interface equipped with a native flash controller (that brings cost and power-efficiency benefits over bridge-based solutions). The Kingston DataTraveler Max USB flash drive (UFD) - another product with a native flash controller - was introduced in August 2021. It advertised 1GBps-class speeds, low power consumption, and a Type-C interface - all in a thumb drive form-factor. Today, Kingston is expanding the DT Max series with three new drives - all sporting a USB 3.2 Gen 2 Type-A interface.

This review digs into all the three capacity points - 256GB, 512GB, and 1TB - in the new DTMAXA series sampled by Kingston. We'll be taking a look at the performance, power efficiency, and value proposition of the DTMAXA. We've also cracked the drive open in order to determine differences between the hardware in the original DT Max and the new DTMAXA products.

Introduction and Product Impressions

Bus-powered external storage devices have grown both in storage capacity and speeds over the last decade. Thanks to rapid advancements in flash technology (including the advent of 3D NAND and NVMe) as well as faster host interfaces (such as Thunderbolt 3 and USB 3.2 Gen 2x2), the market has seen the introduction of palm-sized flash-based storage devices capable of delivering 2GBps+ speeds.

The thumb drive form factor is attractive for multiple reasons - there is no separate cable to carry around, and the casing can be designed to include a keyring loop for portability. Vendors such as Corsair and Mushkin briefly experimented with SATA SSDs behind a USB bridge chip, but the thermal solution and size made the UFDs slightly unwieldy. The introduction of high-performance native UFD controllers last year from Phison and Silicon Motion has made this category viable again.

Kingston's DT Max series retains the traditional DataTraveler thumb drive form-factor. However, it takes full advantage of the USB 3.2 Gen 2 connector by promising 1GBps speeds. Available in three capacities - 256GB, 512GB, and 1TB, and in both Type-C and Type-A connector versions, Kingston says that they can deliver those high speeds across all six SKUs. We had done a thorough investigation into the 1TB capacity point of the DT Max Type-C version last year. Kingston claims that the new Type-A additions to the DT Max series are the same as the corresponding Type-C ones in terms of performance, capacity, and form factor, except for minor changes to the color and Type-A connector. We set out to confirm those claims.

The new Type-A series shares the same sliding cap design to protect the connector. The blue LED power indicator and keyring loop are retained. The new connector makes it necessary to slightly lengthen the UFD and also adds a couple of grams to the weight - specifics in the table at the end of this section.

The teardown process was similar to that of the Type-C version. With no screws in the design, everything is held by small plastic tabs. Other than the connector change, the only difference we could spot on the board was the updated flash package part number. While last year's Type-C version used the FPxxx08UCM1-7D (with Micron's 96L 3D TLC), the new DTMAX series uses the FBxxx08UCT1-AF (with Toshiba's BiCS5 112L 3D TLC). It is not clear whether newer production runs of the Type-C versions have also shifted the flash parts - we can only comment on our review samples. Kingston continues to retain the Silicon Motion SM2320 native UFD controller.

Since the publication of our DataTraveler Max Type-C review, we have processed a number of different drives with our updated testbed and test suite. For comparison purposes, we have chosen a number of 1TB and smaller-sized direct-attached storage (DAS) devices.

CrystalDiskInfo provides a quick overview of the capabilities of the internal storage device. Since the program handles each bridge chip / controller differently, and the SM2320 has not yet found its way into the tracked controllers, many of the entries are marked as vendor-specific, and some of the capabilities (such as the interface) are deciphered incorrectly. The temperature monitoring worked well, though - just like it did for the Type-C version.

S.M.A.R.T Passthrough - CrystalDiskInfo

The table below presents a comparative view of the specifications of the different storage bridges presented in this review.

Comparative Direct-Attached Storage Devices Configuration
Aspect
Downstream Port Native Flash Native Flash
Upstream Port USB 3.2 Gen 2 Type-A (Male) USB 3.2 Gen 2 Type-C (Male)
Bridge Chip Silicon Motion SM2320 Silicon Motion SM2320
Power Bus Powered Bus Powered
     
Use Case 1GBps-class, compact USB thumb drive with retractable cover for Type-A connector 1GBps-class, compact USB thumb drive with retractable cover for Type-C connector
     
Physical Dimensions 91.2 mm x 22.3 mm x 9.5 mm 82.6 mm x 22.3 mm x 9.5 mm
Weight 14.5 grams 12.5 grams
Cable N/A N/A
     
S.M.A.R.T Passthrough Yes Yes
UASP Support Yes Yes
TRIM Passthrough Yes Yes
Hardware Encryption Not Available Not Available
     
Evaluated Storage Toshiba BiCS5 112L 3D TLC Micron 96L 3D TLC
     
Price USD 180 USD 180
Review Link Kingston DTMAXA/1TB Review Kingston DT Max 1TB Review

Prior to looking at the benchmark numbers, power consumption, and thermal solution effectiveness, a description of the testbed setup and evaluation methodology is provided.

Testbed Setup and Evaluation Methodology

Direct-attached storage devices (including thumb drives) are evaluated using the Quartz Canyon NUC (essentially, the Xeon / ECC version of the Ghost Canyon NUC) configured with 2x 16GB DDR4-2667 ECC SODIMMs and a PCIe 3.0 x4 NVMe SSD - the IM2P33E8 1TB from ADATA.

The most attractive aspect of the Quartz Canyon NUC is the presence of two PCIe slots (electrically, x16 and x4) for add-in cards. In the absence of a discrete GPU - for which there is no need in a DAS testbed - both slots are available. In fact, we also added a spare SanDisk Extreme PRO M.2 NVMe SSD to the CPU direct-attached M.2 22110 slot in the baseboard in order to avoid DMI bottlenecks when evaluating Thunderbolt 3 devices. This still allows for two add-in cards operating at x8 (x16 electrical) and x4 (x4 electrical). Since the Quartz Canyon NUC doesn't have a native USB 3.2 Gen 2x2 port, Silverstone's SST-ECU06 add-in card was installed in the x4 slot. All non-Thunderbolt devices are tested using the Type-C port enabled by the SST-ECU06.

The specifications of the testbed are summarized in the table below:

The 2021 AnandTech DAS Testbed Configuration
System Intel Quartz Canyon NUC9vXQNX
CPU Intel Xeon E-2286M
Memory ADATA Industrial AD4B3200716G22
32 GB (2x 16GB)
DDR4-3200 ECC @ 22-22-22-52
OS Drive ADATA Industrial IM2P33E8 NVMe 1TB
Secondary Drive SanDisk Extreme PRO M.2 NVMe 3D SSD 1TB
Add-on Card SilverStone Tek SST-ECU06 USB 3.2 Gen 2x2 Type-C Host
OS Windows 10 Enterprise x64 (21H1)
Thanks to ADATA, Intel, and SilverStone Tek for the build components

The testbed hardware is only one segment of the evaluation. Over the last few years, the typical direct-attached storage workloads for memory cards have also evolved. High bit-rate 4K videos at 60fps have become quite common, and 8K videos are starting to make an appearance. Game install sizes have also grown steadily even in portable game consoles, thanks to high resolution textures and artwork. Keeping these in mind, our evaluation scheme for portable SSDs and UFDs involves multiple workloads which are described in detail in the corresponding sections.

  • Synthetic workloads using CrystalDiskMark and ATTO
  • Real-world access traces using PCMark 10's storage benchmark
  • Custom robocopy workloads reflective of typical DAS usage
  • Sequential write stress test

In the next section, we have an overview of the performance of the Kingston DTMAXA drives in these benchmarks. Prior to providing concluding remarks, we have some observations on the UFD's power consumption numbers and thermal solution also.

Performance Benchmarks
POST A COMMENT

17 Comments

View All Comments

  • ISOProPlus6.89ghz - Monday, July 18, 2022 - link

    Im sorry I guess I’m a little bit confused? If you’re transferring large files and they are important shouldn’t they be used on an external ssd with better reliability not a usb drive? I just don’t understand what this usb drive would be used for that fully uses the speeds that has a better more reliable and basically the same portability? Reply
  • ISOProPlus6.89ghz - Monday, July 18, 2022 - link

    “ that has a better more reliable and basically the same probability”

    Should be replaced with

    *That would not be better suited for another solution that is more reliable and safer for the data and might be faster with the same portability maybe a tiny cable*
    Reply
  • abufrejoval - Saturday, July 23, 2022 - link

    The significance of these devices is that they eliminate the distinction.

    They are no longer "USB sticks", but external SSDs in a USB stick form factor.

    You could of course just add a cable in the middle, if you wanted some flexibility.
    Or add steel cover for the "shit happens" protection.

    Of course a USB stick usually sticks out and therefore adds quite a bit of potential fragility to a notebook you might be moving around while working.

    I have some USB media that is so small it almost disappears inside a USB-A connector... which doesn't quite eliminate the fragility nor offers quite that level of performance yet.

    We used to have PCMCIA, CompactFlash and all sorts of other media that could disappear inside laptops and thus be safer from accidental destruction.

    For a while I enjoyed notebooks that still had a CD/DVD drive bay with a SATA connector: with a simple plastic caddy I could then put a SATA-SSD in there and basically get a hot-swap tray for the notebook.

    µSD cards are getting to SATA levels today and NVMe class performance may be not too far away.

    I use these sticks mostly with NUCs, which are both stationary and rather painful when it comes to swapping storage e.g. to boot another OS. They are usually out of the "conflict zone" of lose hands yet within reach, so fragility is a very unlikely problem while the flexibility is a big bonus.

    For very mobile laptops or big workstations something different might work better, but I appreciate the choice.
    Reply
  • ralphthemagician - Thursday, September 8, 2022 - link

    The reliability here is likely more than enough for many (most?) use cases. They don't publish TBW, but even the absolute worst case scenarios is likely more than adequate for basic backup.

    I actually decided to start using these sticks for backup since they are so cheap (the 1TB USB-C version is on sale for $135 right now). I was considering maybe getting an enclosure and some NVMe sticks with published TBW specs, but decided it wasn't worth it. It is probably more likely I would damage something swapping NVMe sticks into an enclosure that just rotating these sticks.

    Even if the TBW is something *insanely* low like 100 TBW these sticks will last me 5+ years if I am only doing a delta backup once a week. But they actually come with a 5 year warranty, which is kind of unheard of at this level. This leads to me believe that the TBW is probably quite respectable.

    Kingston has the XS2000 too, which is twice as fast, goes up to 4TB, and comes in different (I guess you could call it "more traditional") form factor. Definitely more physically robust, but I'm not really transporting these anywhere. What's nice about these sticks, IMO, is you can label them and put them on a keychain and just keep them in a desk.
    Reply
  • Arbie - Tuesday, July 19, 2022 - link

    Wow - what a thorough report! Like a technical white paper. Thanks. Reply
  • Chrestos SV1GAP - Friday, September 16, 2022 - link

    @ page 3:
    "USB 2.0 ports are guaranteed to deliver only 4.5W (900mA @ 5V)"
    You mean:
    "USB 2.0 ports are guaranteed to deliver only 2.5W (500mA @ 5V)" or
    "USB 3.0 ports are guaranteed to deliver only 4.5W (900mA @ 5V)"
    Does the 2.31W and 2.37W mean that it can operate in even a USB 2.0 port with just 500mA maximum capacity?
    Reply
  • Chrestos SV1GAP - Friday, September 16, 2022 - link

    Design a version of "Kingston DTMAXA" with much smaller length.
    https://www.kingston.com/en/usb-flash-drives/datat...
    From https://www.kingston.com/datasheets/dtmaxa_en.pdf
    "Dimensions
    Type-C: 82.17 mm x 22.00 mm x 9.02 mm
    Type-A: 91.17 mm 22.00 mm x 9.02 mm"

    The length of 91.17 mm is problematic. The lever of 91.17 mm produces large "moment of force".
    Instead of 91.17 mm x 22.00 mm x 9.02 mm, use 55 mm x 20...40 mm x 15...20 mm.
    If it is too wide, it is going to be incompatible with some positionings.

    Scenario 1
    50 mm x 22 mm x 25 mm works fine for my needs. (25 mm is the thickness of a 92*92*25 fan that I use vertically on the side of a laptop.)
    Use the length of DataTraveler G4.
    Place the USB plug asymmetrically with respect to the height of 15...20 mm, so as the lower side doesn't get disturbed by the table.
    Ie imagine a DataTraveler G4 (without the USB plug) on top of another one (with the USB plug).

    Scenario 2
    The 55 mm x 22 mm x 20 mm arrangement perhaps requires 2 PCBs, one on top of the other. Perhaps with 1 PCB the construction is difficult.
    You could use 1 PCB and a case of 50...55 mm x 35...40 mm x 10 mm.
    I repeat, it is going to be incompatible with some positionings.
    Reply

Log in

Don't have an account? Sign up now